What Size Inverter Do I Need for My RV? Sizing Guide
Disclosure: this post contains affiliate links. If you buy through them, ReneEnergy may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
What size inverter do I need for my RV? Add up the watts of every AC appliance you will run at the same time, add some headroom, and pick a pure sine wave inverter whose continuous rating covers that total and whose surge rating covers any motor or compressor start. For most RVs that means about 1,000 W for laptops, TVs and chargers, or about 2,000 W if you want to run a coffee maker or microwave off the batteries.
Quick answer: An RV inverter should be sized to your largest simultaneous AC load, not your daily energy use. A laptop and TV need well under 1,000 W, while a 1,200 W coffee maker plus small loads pushes you to a 2,000 W class unit. Bigger inverters also pull more current from a 12 V battery and need heavier cable and fusing.
By Alex, ReneEnergy. Last updated November 22, 2026.
What size inverter do I need for my RV, step by step?
Size the inverter in four steps, using the watt label on each appliance or its manual:
List your AC loads. Only things that plug into a 120 V outlet count. 12 V DC devices such as lights and water pumps run from the battery directly, not through the inverter.
Find the biggest group you will run at once. Virginia Cooperative Extension's 2020 appliance guide lists typical ratings of 900–1,200 W for a coffee maker, 750–1,100 W for a microwave and 1,200–1,875 W for a hair dryer, against about 50 W for a laptop and about 120 W for a flat-screen TV [1].
Add headroom. In the example below we add 25% so the inverter is not running flat out. That figure is our planning assumption, not a standard.
Check surge. Motors and compressors pull extra power for a moment when they start. Inverter makers publish a separate surge or peak rating for this, such as 4,000 W surge on a 2,000 W Renogy P2 [2].
Worked example: three RV load scenarios
This is an illustrative calculation, not a measurement. Appliance watts come from the upper end of the Virginia Cooperative Extension ranges [1]. Battery current assumes a 12 V system and 90% inverter efficiency, in line with the "over 90%" nominal efficiency Renogy publishes for its P2 inverters [2][3]. Arithmetic was run in Python.
Scenario (running at the same time) | AC load (W) | With 25% headroom (W) | Approx. battery current at 12 V (A) | Inverter class that fits |
Laptop (50 W) + flat-screen TV (120 W) | 170 | 212 | 15.7 | 300–1,000 W |
Coffee maker (1,200 W) + laptop + TV | 1,370 | 1,712 | 126.9 | 2,000 W |
Microwave (1,100 W) + coffee maker (1,200 W) | 2,300 | 2,875 | 213.0 | 3,000 W, or run them one at a time |
The current column is the part many RV owners miss. Battery current is roughly AC watts ÷ (battery volts × efficiency), so 1,370 W ÷ (12 V × 0.9) ≈ 127 A. Simply making coffee and microwaving breakfast one after the other, instead of together, keeps you in the 2,000 W class.
Energy use is a separate question from inverter size. Using the U.S. Department of Energy formula, watts × hours ÷ 1,000 gives kWh [4]. A 1,200 W coffee maker running for 10 minutes uses 200 Wh of AC power, or about 222 Wh from the battery at 90% efficiency, which is roughly 18.5 Ah from a 12 V bank. That is why your choice of RV house battery matters as much as the inverter.
Pure sine wave or modified sine wave for an RV?
Choose pure sine wave for an RV. It produces the same kind of AC as a household outlet, which suits laptops, TV power supplies, chargers and appliances with motors. Renogy, for example, specifies total harmonic distortion below 3% on linear loads for its 2,000 W pure sine wave model [2]. Modified sine wave units may not suit every device, so check your appliance manuals before you consider one.
Why does a bigger RV inverter need bigger cables and a fuse?
Because current rises with load. In the table above, a 2,300 W load pulls around 213 A from a 12 V battery. Cable size, fuse rating and terminal size must come from the inverter maker's manual. Victron's datasheet for the Phoenix 12/1200, for example, lists a maximum battery cable size of 35 mm² (2 AWG) for its screw terminals [5]. Renogy lists M8 battery terminals on its 2,000 W P2 [2]. If you are planning 3,000 W or more on a 12 V system, a 24 V or 48 V bank halves or quarters the current for the same watts, but that changes the whole system and is a job for a professional.
How much power does an RV inverter use when nothing is plugged in?
Every inverter draws a little power just by being switched on. Victron lists 11 W at zero load for the Phoenix 12/1200, or 1 W in its ECO search mode [5]. Renogy lists a no-load draw below 1 A for its 1,000 W P2 and below 2 A for its 2,000 W P2 [3][2]. Over 24 hours, 11 W adds up to 264 Wh, so switch the inverter off, or use a power-saving mode, when you are not using AC power.
How to choose an RV inverter
Continuous watts: at least your largest simultaneous load plus headroom.
Surge watts: enough for motor and compressor starts.
Battery voltage: match your bank (12 V in most RVs and vans).
Waveform: pure sine wave.
Idle draw: lower is better for boondocking.
Listings: look for a published safety listing, such as the ETL listing to UL 458 that Renogy states for its P2 inverters [2][3].
Weight and warranty: check both on the spec sheet.
RV inverters that match these sizes
These picks are based on published manufacturer specs, not hands-on testing. Check the current listing and manual before you buy.
Model | Continuous (W) | Surge/peak (W) | Efficiency | Idle draw | Weight | Listing / warranty |
Victron Phoenix 12/1200 120V VE.Direct | 1,200 | 1,600 (15 s) | 91% max | 11 W (1 W ECO) | 15 lb | See maker's documentation |
Renogy P2 1000W 12V | 1,000 | 2,000 | >90% nominal | <1 A | 6.0 lb | ETL listed to UL 458 / 1 year |
Renogy P2 2000W 12V | 2,000 | 4,000 | >90% nominal | <2 A | 11.7 lb | ETL listed to UL 458 / 1 year |
Renogy P2 1000W Pure Sine Wave Inverter (12 V): fits the light-use scenario of laptops, TV and chargers, with a low idle draw [3].
Victron Phoenix Inverter 12/1200 120V VE.Direct (GFCI outlet): a compact 1,200 W option with an ECO mode for long boondocking stays [5].
Renogy P2 2000W Pure Sine Wave Inverter (12 V): covers the coffee-maker scenario, with a 4,000 W surge rating [2].
FAQ
Will a 2,000 W inverter run an RV microwave?
Usually yes, if the microwave is the main load. Typical microwaves are rated 750–1,100 W [1], which fits within 2,000 W continuous. Check the input rating on your microwave's label and use that number.
Can I run my RV air conditioner on an inverter?
It is possible but demanding, because a roof air conditioner draws a lot of power for hours, not minutes. Check the AC unit's running and starting ratings first, then size both the inverter surge rating and the battery bank around them, ideally with a qualified RV technician.
Is a bigger inverter always better?
No. A larger inverter usually has a higher idle draw, costs more, weighs more and needs heavier cables and fusing. Size for the loads you will actually run together.
Safety note
This article is general information, not electrical advice. Inverter installation, battery cabling, fusing and any connection to shore power or the RV's AC panel should be done or checked by a qualified RV technician or licensed electrician, following the manufacturer's manual.
Thinking about going solar at home too?
If sizing your RV system has you thinking about solar for your house, we can help you take the next step. Get your personalized solar quote.
Related reading
Sources
Virginia Cooperative Extension, "Estimating Appliance and Home Electronic Energy Use" (2020)
Renogy, 2000W 12V Pure Sine Wave Inverter specifications (RNG-INVT-2000-12V-P2-US)
Renogy, 12V 1000W Pure Sine Wave Inverter specifications (RNG-INVT-1000-12V-P2-US)
U.S. Department of Energy, "Estimating Appliance and Home Electronic Energy Use"
Victron Energy, Phoenix Inverter VE.Direct 250W–1600W 120V datasheet
Fact-checked November 22, 2026.



Comments